What is best to buff dull alluminum grille? |
Post Reply |
Author | |
GoldFinger
Senior Member Joined: 03-April-2015 Location: North Carolina Status: Offline Points: 295 |
Post Options
Thanks(0)
Posted: 20-September-2015 at 1:19PM |
Hello!
I am curious to know what tool and polish to buff my dull aluminum trim on the outer part of my 73 Torino Sport grille? Weinal?..Dremel tool?..Any help and suggestions would be appreciated! Thanks!
|
|
californiajohnny
Moderator Group Joined: 05-October-2013 Location: winlock, wa Status: Offline Points: 14609 |
Post Options
Thanks(0)
|
dremel would work but is kinda small. i'd use a small 2" dia. cotton buffing pad like this:
you can use it in a drill,or better yet a air die grinder (if you have a air compressor) if you have a harbor freight near you they have these, for a few dollars. and die grinders for $10-$15! they work fine for the money (i have several) and for buffing compound: probably a small brick of red rouge if you do it on the car... i'd suggest masking tape to mask off and protect the paint!!! you can use wenal or similar product to hand polish after the buffing but remember the trim is clear anodized, so it will clean up some but it won't look like fine polished aluminum unless you sand and buff down past that hard anodized layer, which i wouldn't do if you don't need to!!! |
|
JOHN
74 GRAN TORINO S&H CLONE 74 VETTE CUSTOM 90 S10 BLAZER 4X4 LIFTED 77 CELICA CUSTOM 75 V8 MONZA SUPERCHARGED 79 COURIER VERT. SLAMMED 75 VEGA V6 5 SPD 70 CHEV C10 P/U 68 MUSTANG FB CONVERSION |
|
twosfamily
Member Joined: 24-June-2012 Location: VT Status: Offline Points: 70 |
Post Options
Thanks(0)
|
What Californiajohnny said x2!
Over the years, however, I have never been really successful (or happy) with just buffing the anodized coating. For me, it never has turned out very well. If you remove the trim from the car and find the buffing does not turn out well, you can sand through the the coating. Sanding through the coating has proven to me to be a very, very time consuming process. There are some chemical products out there that work well for removing the coating in little time. Years ago, I used heavy duty oven cleaner (if you go this route, do so in a very well ventilated area!). That has worked well for me. You have to make sure you let the piece soak in the cleaner. I would place it in a container and spray it down until the piece is completely covered with the cleaner, like a bath. Within the last several years I have used Draino Max Gel with even better success. It works extremely well and because it is a gel, it covers the part with enough product much easier. As a container, I use PVC pipe cut in half. That will let the parts bath in the Gel while using minimal product and with longer pieces of PVC, you can fit longer pieces of trim. It usually takes 15-20 minutes of soaking until all the coating is removed. After the coating is removed, remove the piece from the solution and rinse it well. You can then work the piece if there are any scratches or dings. Scratches can be sanded out in steps. Dings can be removed with a trim dolly and trim hammer. I have found that there are not many small defects (and most large ones!) that can not be removed easily, with just some time! Then you can polish the piece to a phenomenal shine with the products Californiajohnny mentions above! I sometimes use Autosol in the polishing process. With being bare polished aluminum, you will have to keep up on polishing it more often. But, it looks great! Or, you can clear coat it, clear powder coat it, or send it out to be re-anodized. Some of which can be costly. This has been my experience with anodized aluminum trim. As with anything, I am sure there are many other ways to do this but this process has always worked very well for me! |
|
robot9000
Senior Member Joined: 02-September-2011 Location: Michigan Status: Offline Points: 505 |
Post Options
Thanks(0)
|
I second what Twosfamily said.
I would remove the trip piece and work on it. Its a lot easier. I too had to remove some dents and ended up removing the anodizing with lye drain cleaner. I could not really polish the annodized parts enough to make them shine like the part missing the anodizing. I bought some Por-15 Glisten to coat the parts, bud have not had time to do that. I plan on removing the grill next spring for some engine work and will touch up the AL and Glisten it then. |
|
1973 Gran Torino Sport
2010 Mazda 6 2007 Jeep Wrangler 2011 Damon Daybreak 35BD |
|
Big Bird
Senior Member Joined: 25-August-2013 Location: New York Status: Offline Points: 4194 |
Post Options
Thanks(0)
|
If you strip the anodizing off, polish with 0000 steel wool, and follow with Mother's polish. If you use a powerball or anything like that, you REALLY want the part off the car.
If you use the red rouge, take it off the car and 100 yards away. It will spatter. You won't notice. It will dry. You will cry. Imagine red birdsh*t drying on your paint.
|
|
"What we do in full frontal view, is more honest than your cleaned-up mind."
Randy 1979 T-Bird 2005 F-150 STX RCSB 4.6, 3.55 LSD How the Heck does a REGULAR CAB SHORTBED weigh over 5200 pounds? |
|
Post Reply | |
Tweet |
Forum Jump | Forum Permissions You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |