molding color, valance bolts, door panel clips |
Post Reply |
Author | ||
fordismyboss
Senior Member Joined: 05-January-2014 Location: SF Bay Area Status: Offline Points: 397 |
Post Options
Thanks(0)
Posted: 01-February-2016 at 4:43PM |
|
Been searching and searching and ........ can't find these!
GTS Door panel insert metal retaining clips: need 6-8 pieces Rear valance bolt and clip: need only one! Found this buried in Dearborn Classics website: Part #: 90-74837-1 Gonna give'm a try Front valance bolt and clip radiator housing side: need two What color is on the molding? Black and an argent gray or light brown? Anyone know? I know this is small stuff but the little stuff just kills you and I can't find these things anywhere. Thank for reading! Edited by fordismyboss - 02-February-2016 at 3:12AM |
||
californiajohnny
Moderator Group Joined: 05-October-2013 Location: winlock, wa Status: Offline Points: 14609 |
Post Options
Thanks(0)
|
|
on the door panel insert clip: i don't know if you can get them anywhere??? unless someone else on here knows ? are yours broken off or ripped out of the masonite part? i ask because i had a few screwed up on mine and fixed them! several were broken off the metal tab from the rest of the metal part... so i carefully tack welded them back with my mig welder then dabbed it with a wet rag!
i had one that was completely ripped out of the masonite panel... so i carefully unpeeled the vinyl upholstery just enough to get access between the vinyl and the panel, i then used a couple of the large copper staples from a cardboard shipping box, using two crisscrossed in an " X " and bent the ends over on the metal side, then carefully hammered them to tighten them up! not perfect, but it was the only thing i could think of that would hold in that tight area without interfering with the panel or show behind the vinyl |
||
JOHN
74 GRAN TORINO S&H CLONE 74 VETTE CUSTOM 90 S10 BLAZER 4X4 LIFTED 77 CELICA CUSTOM 75 V8 MONZA SUPERCHARGED 79 COURIER VERT. SLAMMED 75 VEGA V6 5 SPD 70 CHEV C10 P/U 68 MUSTANG FB CONVERSION |
||
legend onirot
Senior Member METAL GOD Joined: 18-January-2009 Location: hattiesburg ms Status: Offline Points: 3038 |
Post Options
Thanks(0)
|
|
i needed two rear valance bolts and clips... couldnt find them, i had to make some.
the molding is black and argent gray. i bought mine in a rattle can from a paint store
|
||
---------------------
malcolm 1973 gran torino sport (formal)... "Stacy Lynn" 1972 gran torino (formal)... "Mackenzie" 1973 gran torino sport (sportroof)... "Leela" |
||
fordismyboss
Senior Member Joined: 05-January-2014 Location: SF Bay Area Status: Offline Points: 397 |
Post Options
Thanks(0)
|
|
The passenger door is perfect, but six of tabs tabs on the driver door panel insert retaining tabs are sheered off for some reason(?). Thank you for the mig weld idea! Also fabricating tabs with copper is a good idea. Would love to find some from a donor too!
|
||
fordismyboss
Senior Member Joined: 05-January-2014 Location: SF Bay Area Status: Offline Points: 397 |
Post Options
Thanks(0)
|
|
Paint - Argent - Genuine Ford - 12 Oz. Spray Can # 90-52421-1
Found this buried on Dearborn Classics website. Not sure why DBC does not connect these products with search criteria(?) |
||
legend onirot
Senior Member METAL GOD Joined: 18-January-2009 Location: hattiesburg ms Status: Offline Points: 3038 |
Post Options
Thanks(0)
|
|
some of the members here may have some of these. there are a few that have scrapped multiple cars and have many parts laying around (cough***joe/unlovedford***cough).
send unlovedford a pm and ask. wouldnt hurt.
|
||
---------------------
malcolm 1973 gran torino sport (formal)... "Stacy Lynn" 1972 gran torino (formal)... "Mackenzie" 1973 gran torino sport (sportroof)... "Leela" |
||
mcford
Senior Member Joined: 31-May-2003 Location: Utica, Michigan Status: Offline Points: 2160 |
Post Options
Thanks(0)
|
|
dARK ARGENT.
|
||
Mike
|
||
unlovedford
Senior Member Joined: 17-December-2010 Location: Tennessee Status: Offline Points: 10142 |
Post Options
Thanks(0)
|
|
I have doors with the moldings still on. Perhaps one will have good ones. I have a few junky GTS panels I can check for those clips.
|
||
Joe
1972 Mom's Squire Wagon 1972 Torino Wagon 1976 Torino 1968 Cougar XR7-First batch 1972 Torino 460 1989 BroncoII/Jeeps/Titanimous Popeye and Brutus (Rams) |
||
73GTS
Senior Member Joined: 22-September-2008 Location: Cleveland, Ohio Status: Offline Points: 945 |
Post Options
Thanks(0)
|
|
I have found a simple, cheap way to fix this issue... Go to Lowes and buy these. Cost me $3.46 per panel... Start by cutting a V in it so it can be inserted... Now a little sanding on each side to make sure it clears the bracket's "Teeth" (hole) Just a little on each side is all that's needed, so don't go crazy... Then gently pry on both sides of the bracket with a screw driver rocking it to give a little clearance... GENTLY! Now insert the clip from one side and rotate in the opposite direction from the place the V will end up. It will come into view as we continue.... If you use pliers, be careful not to damage the splines. It may be tough to turn so you will need help. Be careful... This is the position you want it to be in... Gently push into place at the base with a screw driver... Just that easy. Fits right into the holes in the panel with a little finagling and holds tight... |
||
Jim
|
||
californiajohnny
Moderator Group Joined: 05-October-2013 Location: winlock, wa Status: Offline Points: 14609 |
Post Options
Thanks(0)
|
|
that's a damn good idea jim! i fixed a couple of mine by tack welding the tab back on and quickly cooling it, had to make one out of a piece of sheet metal. but one was ripped out of the masonite, so i carefully worked the vinyl loose just enough to reach between it to put a couple of copper packaging staples through it and crimp them tight against the metal part! (actually they may have been from the box that had the dash pad i got from you )
|
||
JOHN
74 GRAN TORINO S&H CLONE 74 VETTE CUSTOM 90 S10 BLAZER 4X4 LIFTED 77 CELICA CUSTOM 75 V8 MONZA SUPERCHARGED 79 COURIER VERT. SLAMMED 75 VEGA V6 5 SPD 70 CHEV C10 P/U 68 MUSTANG FB CONVERSION |
||
unlovedford
Senior Member Joined: 17-December-2010 Location: Tennessee Status: Offline Points: 10142 |
Post Options
Thanks(0)
|
|
That is a superb idea. Good job.
|
||
Joe
1972 Mom's Squire Wagon 1972 Torino Wagon 1976 Torino 1968 Cougar XR7-First batch 1972 Torino 460 1989 BroncoII/Jeeps/Titanimous Popeye and Brutus (Rams) |
||
73GTS
Senior Member Joined: 22-September-2008 Location: Cleveland, Ohio Status: Offline Points: 945 |
Post Options
Thanks(0)
|
|
Finished it all up today. Here's what it looks like...
|
||
Jim
|
||
californiajohnny
Moderator Group Joined: 05-October-2013 Location: winlock, wa Status: Offline Points: 14609 |
Post Options
Thanks(0)
|
|
|
||
JOHN
74 GRAN TORINO S&H CLONE 74 VETTE CUSTOM 90 S10 BLAZER 4X4 LIFTED 77 CELICA CUSTOM 75 V8 MONZA SUPERCHARGED 79 COURIER VERT. SLAMMED 75 VEGA V6 5 SPD 70 CHEV C10 P/U 68 MUSTANG FB CONVERSION |
||
73GTS
Senior Member Joined: 22-September-2008 Location: Cleveland, Ohio Status: Offline Points: 945 |
Post Options
Thanks(0)
|
|
Also...another great tip!
Use Great Planes Pro CA cyanoacrylate glue. (Thin-instant). Amazing stuff to fix door panels with. I glued some of the metal clips on. You would have to rip them off. Also used for door panels that the holes are pulled out of. Makes them strong to put clip back into. |
||
Jim
|
||
Post Reply | |
Tweet |
Forum Jump | Forum Permissions You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |