460 exhaust gaskets & hardware |
Post Reply |
Author | |
TV 2M8O
Senior Member Joined: 20-September-2006 Location: Southern Ohio Status: Offline Points: 2045 |
Post Options
Thanks(0)
Posted: 06-July-2016 at 12:11AM |
With engine installation just ahead, I have ordered the following exhaust gaskets, gasket coating and hardware:
Remflex 3011 Exhaust Gasket for Ford 429/460 V8 Engine, (Set of 2) Permatex 80697 Copper Spray-A-Gasket Hi-Temp Adhesive Sealant, 9 oz. net Aerosol Can Mr. Gasket 2231G Headlock Locking Header Bolt, (Set of 16) My selections were based upon reading thru several threads here on the forum. Anything I may have overlooked? Thanks for your input!
|
|
TV 2M8O OUT JOE 1976 Gran Torino S&H season 2-4 Clone Project Blog: http://tv2m8o.blogspot.com/ |
|
TV 2M8O
Senior Member Joined: 20-September-2006 Location: Southern Ohio Status: Offline Points: 2045 |
Post Options
Thanks(0)
|
The Mr Gasket Headlock bolts are going back.... too short! They measure 3/4" and with the thick flange on the Crites' headers and the thick Remflex gasket, they aren't gonna work. Picking up some 1" header bolts on my next trip into Summitt Racing.
Edited by TV 2M8O - 21-July-2016 at 1:29PM |
|
TV 2M8O OUT JOE 1976 Gran Torino S&H season 2-4 Clone Project Blog: http://tv2m8o.blogspot.com/ |
|
TV 2M8O
Senior Member Joined: 20-September-2006 Location: Southern Ohio Status: Offline Points: 2045 |
Post Options
Thanks(0)
|
**CLICK ON PICS TO ENLARGE AND CLICK AGAIN TO SUPERSIZE**
as well as the Remflex header gaskets.... Since the Crites 460 headers have individual header flanges, I trimmed the Remflex gaskets to the shape of the flanges.... I shot the gaskets with a light coat of the adhesive on the block side just to hold them in place while the headers were installed one tube at a time (FYI, the contoured shape of the gasket goes down and the angle cut is the top). Once they were all hung... and the collectors installed... the header bolts were torqued to 20ft/lbs. Will have to wait until I light this baby off before I'll know how well the gaskets perform! Edited by TV 2M8O - 11-September-2016 at 3:54AM |
|
TV 2M8O OUT JOE 1976 Gran Torino S&H season 2-4 Clone Project Blog: http://tv2m8o.blogspot.com/ |
|
californiajohnny
Moderator Group Joined: 05-October-2013 Location: winlock, wa Status: Offline Points: 14606 |
Post Options
Thanks(0)
|
after you've run it a bit and drove it some recheck those header bolts every so often
|
|
JOHN
74 GRAN TORINO S&H CLONE 74 VETTE CUSTOM 90 S10 BLAZER 4X4 LIFTED 77 CELICA CUSTOM 75 V8 MONZA SUPERCHARGED 79 COURIER VERT. SLAMMED 75 VEGA V6 5 SPD 70 CHEV C10 P/U 68 MUSTANG FB CONVERSION |
|
aquartlow
Senior Member Joined: 19-December-2011 Location: Summerfield, Fl Status: Offline Points: 2270 |
Post Options
Thanks(0)
|
When I installed my coated headers, I used 3/8" thin width stainless steel washers so as to not have the header bolts tighten against the finish and screwing it up. Basically the washer sits against the header flange but doesn't scar the flange when tightening the bolt. Good choice on 1" bolts, looking back I should have used SS bolts, I used plated bolts for a better look/corrosion resistance.....they still rusted . Nice BBF install!!
|
|
www.supermotors.net/22468
Yeah, It's a Hybrid...It burns gas and tires. No matter how good she looks, somebody, somewhere, is tired of her sh*t. Beauty is skin deep, ugliness goes clear to the bone. |
|
Post Reply | |
Tweet |
Forum Jump | Forum Permissions You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |