Headlight bezel kit |
Post Reply |
Author | |
Spencer
Member Joined: 07-January-2020 Location: Ny Status: Offline Points: 57 |
Post Options
Thanks(0)
Posted: 07-January-2020 at 4:26PM |
hey everyone, I'm looking for a part and I dont know where to find it. It's the headlight bezel screw kit. Are there any websites or catalogs that might have it?
|
|
californiajohnny
Moderator Group Joined: 05-October-2013 Location: winlock, wa Status: Offline Points: 14609 |
Post Options
Thanks(0)
|
welcome! try mac's or autokrafters, actually you may be able to get some at a local hardware store i did in stainless for my 74 they were a #8 taper head phillips...
|
|
JOHN
74 GRAN TORINO S&H CLONE 74 VETTE CUSTOM 90 S10 BLAZER 4X4 LIFTED 77 CELICA CUSTOM 75 V8 MONZA SUPERCHARGED 79 COURIER VERT. SLAMMED 75 VEGA V6 5 SPD 70 CHEV C10 P/U 68 MUSTANG FB CONVERSION |
|
Spencer
Member Joined: 07-January-2020 Location: Ny Status: Offline Points: 57 |
Post Options
Thanks(0)
|
Ok thanks I'll try that
|
|
Spencer
Member Joined: 07-January-2020 Location: Ny Status: Offline Points: 57 |
Post Options
Thanks(0)
|
do you know what the part is called that the 8 taper head phillips screws into I'm missing that also. On my car I only have one on the right side and it's a little plastic box about a half inch long and that 8 taper head phillips screws into it. The little plastic piece goes into a square hole on the frame next to the head light haha dont know y I'm having such a problem with this, thanks for the help
|
|
californiajohnny
Moderator Group Joined: 05-October-2013 Location: winlock, wa Status: Offline Points: 14609 |
Post Options
Thanks(0)
|
my 74 plastic pieces i was able to find in the dorman/help section at the local parts store about 1/4" square...
|
|
JOHN
74 GRAN TORINO S&H CLONE 74 VETTE CUSTOM 90 S10 BLAZER 4X4 LIFTED 77 CELICA CUSTOM 75 V8 MONZA SUPERCHARGED 79 COURIER VERT. SLAMMED 75 VEGA V6 5 SPD 70 CHEV C10 P/U 68 MUSTANG FB CONVERSION |
|
Spencer
Member Joined: 07-January-2020 Location: Ny Status: Offline Points: 57 |
Post Options
Thanks(0)
|
ok thanks appreciate the help
|
|
schufitz
Member Joined: 23-February-2014 Location: Hammond IN Status: Offline Points: 144 |
Post Options
Thanks(0)
|
Not sure if you mean the bucket adjustment screws with plastic insert or the screws for the grill bezel surrounds at the headlights (?). The adjustment ones are available with the plastic insert:
I reconditioned them on my '69 Torino. Here's where they mount: Here is the grill screw (4 per side), not sure on a source for these as I only needed one and a guy from another site had one |
|
Spencer
Member Joined: 07-January-2020 Location: Ny Status: Offline Points: 57 |
Post Options
Thanks(0)
|
its the headlight bezel that attaches to the grill. The bezel has a clip up top that slides behind the grill and the bottom is held on by a screw/nylon nut. The bezel hole is 3/16 but the nylon nut that sticks out that the screw goes into has a hole that 1/4 wide. I'm not sure if that hole is stripped or what. I also need that nylon nut. Is that the link you put up or is that for the light ajustment set screw? I would put up a pic but am not sure how to. I'm still figuring this forum out. Think I'm still to new to it to put anything up
|
|
schufitz
Member Joined: 23-February-2014 Location: Hammond IN Status: Offline Points: 144 |
Post Options
Thanks(0)
|
I see from your other post you have a '68. Those had 1 piece grille and the '69 had a 3 piece, so previous reply not much help. The link was for the adjustment screws
'68 '69
|
|
schufitz
Member Joined: 23-February-2014 Location: Hammond IN Status: Offline Points: 144 |
Post Options
Thanks(0)
|
Found this in a manual I had, way different than the 69
Edited by schufitz - 10-January-2020 at 6:28PM |
|
Spencer
Member Joined: 07-January-2020 Location: Ny Status: Offline Points: 57 |
Post Options
Thanks(0)
|
Number 3 is the part I'm looking for thank you. Where can I go to put that part number in is there a web site I can use to get it? Thanks again for all the help everyone
|
|
schufitz
Member Joined: 23-February-2014 Location: Hammond IN Status: Offline Points: 144 |
Post Options
Thanks(0)
|
E bay? or try to make a Mustang part work? Edited by schufitz - 12-January-2020 at 6:02AM |
|
Spencer
Member Joined: 07-January-2020 Location: Ny Status: Offline Points: 57 |
Post Options
Thanks(0)
|
just order the ones from the first link that was a big help thanks
|
|
Spencer
Member Joined: 07-January-2020 Location: Ny Status: Offline Points: 57 |
Post Options
Thanks(0)
|
hey so that first link worked I put it on my car and it work great I just need one more any ideas?
|
|
Post Reply | |
Tweet |
Forum Jump | Forum Permissions You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |