Hooker headers 6915hkr |
Post Reply | Page <12 |
Author | |
AUS GTS
Senior Member Joined: 26-July-2021 Location: Australia Status: Offline Points: 383 |
Post Options
Thanks(0)
|
Just to set the record straight for anyone looking at the 6915 HKR, I have just had them fitted to my 73 GTS Q code, t-bar & they fitted up great.
|
|
Al
|
|
72 RS 351
Senior Member Joined: 04-September-2014 Location: Knoxville TN Status: Offline Points: 2765 |
Post Options
Thanks(0)
|
Do they tuck up under the body well and not hang too low below the floor pan? I'll probably buy those and also call them to ask if they'd coat them shortly after getting them. I'll replace the collector flange with a V-band flange, those seal better than the regular type.
|
|
Don
73 Ranchero "Sport 72 front end", floor shift/console, planning EFI 7000+ rpm 351-4V &4R70W 73 Ranchero GT 351C-4V &4R70W for sale later. 92 Lincoln Mark VII SE GTC, OBDII 347/4R70W |
|
AUS GTS
Senior Member Joined: 26-July-2021 Location: Australia Status: Offline Points: 383 |
Post Options
Thanks(0)
|
Yes being a 4 into 1 they do hang lower.... mine have about 4.5" clearance, but the car is lowered about 1.5".
|
|
Al
|
|
AUS GTS
Senior Member Joined: 26-July-2021 Location: Australia Status: Offline Points: 383 |
Post Options
Thanks(0)
|
Hey Don, hang on to your old 4v manifolds, apparently theres a market for them. You may be able to claw back some $.
|
|
Al
|
|
72 RS 351
Senior Member Joined: 04-September-2014 Location: Knoxville TN Status: Offline Points: 2765 |
Post Options
Thanks(1)
|
Yes, tough call some people make to go to LT or stick with stock manifolds. My 73 to sell has stock manifolds, I'm resisting a tear down and refresh. It's a mild build and I'd like it to have better intake, carb, headers, and cam etc. My keeper will be built from scratch with my original 351C engine, I let go of the stock 4V manifolds in about 1980.
|
|
Don
73 Ranchero "Sport 72 front end", floor shift/console, planning EFI 7000+ rpm 351-4V &4R70W 73 Ranchero GT 351C-4V &4R70W for sale later. 92 Lincoln Mark VII SE GTC, OBDII 347/4R70W |
|
AUS GTS
Senior Member Joined: 26-July-2021 Location: Australia Status: Offline Points: 383 |
Post Options
Thanks(0)
|
I just measured the ground clearance & its 3"..... soz fella we're more metrically inclined over here!
|
|
Al
|
|
kychevyguy
Senior Member Joined: 16-December-2013 Location: Lexington KY Status: Offline Points: 1996 |
Post Options
Thanks(0)
|
Following....
|
|
JT, USAF Ret./Architect
1971 Ford F100 "Lizzy" 1971 Cougar XR7 "Kitty" 1984 Chevy Silverado "Sylvia" 2009 Smart Fortwo Cabrio "Lil Dude" 2015 Volvo XC60 R-Design "Sven" |
|
Post Reply | Page <12 |
Tweet |
Forum Jump | Forum Permissions You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |